Brief analysis of detailed installation steps of hydraulic lifting column

Detailed installation steps of hydraulic lifting column

Due to the continuous improvement of anti-terrorism awareness, people pay more and more attention to the safety of equipment. Now, hydraulic lifting column equipment can be seen everywhere in major cities, especially in the entrance and exit of government organs, hospitals, schools and other important units with large flow of people. But in such a popular era, hydraulic lifting column equipment operating details and considerations, you are clear? If you are not clear, please go on to read, Xi 'an hydraulic lifting column with you to understand the operation of the hydraulic lifting column and daily use of matters needing attention.

Installation and commissioning requirements

1. Digging foundation holes:

Dig the foundation pit according to the outline size of the product. The size of the foundation pit: length: determine the size according to the situation of the road on site;

Width: 600-800 mm;

Depth: 1400mm(including a seepage layer of 300mm).

2. Make seepage layer:

After mixing with sand and gravel, make 300mm permeable layer from the bottom of the foundation pit upwards. The permeable layer shall be paved and tamped to prevent the equipment from sinking. (If possible, choose gravel below 10mm instead of sand.) According to the different conditions of the region to choose whether to do drainage.

3. Leveling the outer cylinder of the product by unloading:

Remove the outer barrel with hexagon socket and place it on the seepage layer. Adjust the levelness of the outer barrel. Make the upper surface of the outer barrel slightly higher than the ground plane for 3-5mm.

4. Embedded wire pipe:

Embed the threading pipe according to the position of the outlet hole reserved on the surface of the outer barrel. The diameter of the threading pipe shall be determined according to the number of lifting columns. Generally, each lifting column shall require one cable of 3*1.5 power line and one control line of 2*0.75 pressure relief solenoid valve. If there is a lamp belt, and one more cable of 2*0.5 power line, the specific use shall be determined before construction according to the needs of customers and the difference of distribution.

5. Debugging:

Switch on the circuit of the equipment, operate the rising and falling, observe the rising and falling of the equipment, adjust the rising height of the equipment, and check whether the equipment has oil leakage phenomenon.

6. Fixed equipment and pouring:

Put the equipment into the pit, backfill the appropriate amount of sand, fix the equipment with stones, and then pour the equipment with C40 concrete slowly and evenly until it is level with the upper surface of the equipment

Control mode of lifting column

1. The wireless remote control controls the rise and fall of the column:

There are three buttons on the wireless remote control: up, down and stop. The wireless remote control can be used to make the device rise and fall. The stop key can be used to stop the action of the device before the action is completed. (According to the different needs of customers)

2. Distribution box buttons control the rise and fall of cylinder body:

The surface of the box body is provided with up, down and stop buttons. This button can be used to make the device go up and down. During the action is not completed, the stop key can be used to realize the device action stop. (According to the different needs of customers)

3. The external button box controls the lifting of the cylinder body:

This button can be used to make the device go up and down. During the action is not completed, the stop key can be used to realize the device action stop. (According to the different needs of customers)

4. Emergency measures for hydraulic lifting column in case of emergency

When the equipment is in the rising state and the power grid is cut off, the distribution box control system cannot be started normally due to the power cut off. The distribution box is equipped with 12V lead-acid battery, in order not to affect the normal traffic of vehicles, usually press the pressure relief combination button -- the drop button and the stop button on the box at the same time. If the cylinder does not move or slide down for a period of time, the downward pressure can be artificially exerted until the cylinder drops to the ground level.

Three, hydraulic lifting column daily matters needing attention

(1) Avoid frequent lifting within a short time, otherwise the motor will be heated and damaged.

(2) Pay attention to pedestrians during ascending operation to avoid injury.

(3) When the cylinder is not working normally, press the stop button once after the rise and fall, so as to avoid the damage of electrical components and the failure to stop, which will cause the motor to burn out.

(4) In the process of use, if it is found that individual lifting column is much higher than other columns, should immediately press the stop button, and observe whether the motor is still working, when the motor has been confirmed to stop, timely contact with the factory.

(5) It is strictly prohibited to fill the gap around the column with silt and debris, so as not to affect the normal lifting of the column.

(6) It is strictly prohibited to mark the cylinder surface to cause damage to the cylinder.

The lifting ground pile is composed of the bottom base, lifting and blocking barrier column, power transmission device, control and other parts. It has a variety of configurations according to different requirements. The lifting column belongs to the equipment that controls the passage of vehicles. It can be used in conjunction with the road gate control system or separately. The lifting column is mainly divided into automatic lifting type, semi-automatic lifting type and fixed type. Automatic lifting type is divided into hydraulic lifting type, electric lifting type. It is specially designed and developed to prevent non-allowed vehicles from breaking into sensitive areas. It has high practicability, reliability and safety.

1. Effective urban traffic control

Fully automatic lifting ground column by hydraulic control of lifting metal cylinder, with a strong impact and impact resistance. They can be inserted into the road to control traffic and parking. Xuzhou Baisheng automatic lifting ground column provides an overall solution, used to replace the guard box, railing, chain and other fixed roadblocks, effectively solve the problem of controlling the parking of vehicles at intersections. The elevating column has multiple USES: setting up pedestrian streets or restricting vehicles during peak hours.

2, good safety performance: it has a strong impact resistance and impact capability, applied to some sensitive areas: embassies, consulates, government agencies, Banks and so on.

3. Good maneuverability: It does not change the layout of the original space, which is mainly attributed to its maneuverability and flexibility as well as its hidden functions. The lifting of the ground column not only ensures the smooth passage of pedestrians, but also effectively controls the passage of vehicles.

Technical parameters: type: hm - y60220 ground out column size: 600 * 219 (mm) embedded box size: 1165 * 610 * 610 size: (+ 300) 1165 * 610 * 610 (mm) cylinder material: standard 6 mm thick 304 stainless steel or steel spray drive mode: one-piece motor voltage miniature hydraulic systems: ac220v50hz rated voltage: ac220v50hz rated power: 200 w speed: about 4 to 6 s/single level of protection: ip67 use frequency: 40 p/h working environment temperature: Operating tips: LED warning lights, 5cm reflective tape applicable places: airports, special military zones, embassies, ports, nuclear power plants, high-end residential areas, financial institutions, commercial blocks, administrative centers, etc